Announcement

Collapse
No announcement yet.

Source for 6015 24V ball bearing fans?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Source for 6015 24V ball bearing fans?

    The fan that cools the motherboard in one of my printers is getting louder -- a bad sign. I can't find a good replacement. Anyone know where I can find a replacement for this 60x60x15 mm cooling fan that draws around 0.1 A? It must be 24v, unfortunately.

    Thank you!

  • #2
    How 'bout 1 of these: https://www.amazon.com/Converter-Red...s%2C165&sr=8-5. That way, you could use any old computer 12v fan. You could even hook up something like a Noctua or other super quiet fan.

    You could also install a simple 120vac to 12vdc or 5vdc wall adapter into the power supply box. Wire it up to the same switch that powers the printer: when the printer is turned on, the fan comes on. You probably have such an adapter already.
    Last edited by Ender5r; 07-15-2020, 01:58 PM.

    Comment


    • #3
      Great ideas! Thank you! I haven't opened it up yet (as long as I hear the noise I know I'm ok, 😅), but I do recall seeing some nice 12v ball bearing fans on Amazon.

      Thanks again

      Comment


      • #4
        BTW, I have gotten much more life from small fans by adding some light lube to them; something like sewing machine oil. What I do is dismount the fan then, very carefully, so I don't get oil on it, or otherwise spoil it, I remove the small label/sticker that's stuck to 1 side of the fan's hub. I do this by using the large, well sharpened, blade of a pocket knife, sliding it very gently under the edge of the label, using a really shallow angle.
        .
        I then add 1 or maybe 2 drops of oil to the bearing that's exposed (be on the lookout for fans that have a rubber seal over the bearing: you have to remove it first, which I do with the tip of the small blade of a pocket knife). I usually spin the fan blades a bit, to see if the oil disappears into the bearing, in which case I add another drop. I do that until I get 1 drop that stays. I then check to see if I got any oil on the surface of the hub. If I see some, I use alcohol to remove it. Finally, I replace the label/sticker and press it firmly down onto the hub.
        .
        To help get oil into the bearing without getting any oil on the surface of the hub, I often, if I have one nearby, will use a small syringe to place the oil right onto the bearing.
        .
        While I'm actually lubing the bearing, I normally leave the label stuck to the blade I used to remove it.
        Last edited by Ender5r; 07-15-2020, 08:32 PM.

        Comment


        • #5
          Thank you for the tips! I've not bothered the past, but this fan is annoying to get at as I have to remove the bed so anything to reduce the MTBF!

          Cheers

          Comment


          • #6
            If you do decide to replace the fan, remember there are now fans that have magnetic bearings: no physical contact between the rotor and the shaft. They advertise something like 80,000 hours, so kinda like LEDs
            Here's 1 you could look at: https://www.amazon.com/SUNON-KDE1206...4870268&sr=8-2. It's a 2-wire (no speed control). I picked that on purpose because I presume you just want it to go on when you power up the printer and stay on until you shut it down.

            Comment


            • #7
              Interesting idea. I'd guess they are quieter too. There is a 24V version too. Now to order and wait until October(!).

              Thanks!

              Comment


              • #8
                Yeah, long shipping times are a lunch bag letdown for sure. OTOH, a little oil could well keep your existing one going until it arrives.

                Comment


                • #9
                  Funny thing. The parts I ordered three weeks ago from China just arrived! I **think** the electronics survived. 😅

                  Click image for larger version  Name:	Box_from_China.jpg Views:	0 Size:	41.8 KB ID:	1865

                  Comment

                  Working...
                  X